Couldn’t ask for a better crew professional service great price
Excellent work and great follow-up. The entire team works closely together and all have strong communication skills that assures transparency from scheduling, customer service, the guys in the field, and leadership back to me as the customer.
The service man was very helpful and nice to work with.
Julian was very professional and friendly. Thank you.
dan was very very friendly and easy to talk to
Black Haak has been servicing our home and rental home for many years. There's no need to shop around when you get great service. Their agents are always friendly, helpful and efficient.
12/14/18 removed old furnace. Installed new daikin furnace. Ran new gas line from 2psi meter into house. Added a manifold for gas and gas piped furnace. Pulled new 4 wire for thermostat and installed new t4 stat. Installed condensate pump for drain to run into then ran hose over ceiling to floor drain in other room by washer. Ran exhaust venting outside to vent furnace. Connected electrical wiring and added outlet on furnace to power condensate pump. Thank you for choosing Black-Haak heating for your heating needs.
Furnace clean and tune. Cycled system. Checked heat exchanger, ok. Checked and cleaned burners and flame sensor. Checked igniter, ok. Checked gas pressures and adjusted to maximize efficiency. Checked for CO in airstream, none found. Normal levels of CO and XS air in exhaust. System operating normal at this time. Quote for whole home dehumidifier send. Job complete. Ac and furnace clean and tune
Performed level 2 furnace cleaning. Burners and flame sensor are rusting out. Heat exchanger is starting to chip in spots. Gas and exhaust levels are normal. No CO detected in the air. Drain is clear. Heat rise was 65 degrees. Unit is operating normally at this time. I also inspected a leak from the humidifier. I found the water panel wasnâ€™t properly placed in the unit. After I made some adjustments, there were no leaks or standing water. Thank you for choosing Black-Haak! Please fill out our
Performed start up on a new furnace. No gas leaks detected. Gas and exhaust levels are normal. No CO detected in the air. Electrical and venting components are properly installed. Drain is working. High limit passed safety test. Heat rise was 39 degrees. Unit is operating normally at this time. I replaced the water panel for the humidifier. Customer wasnâ€™t home so we will collect the payment later. Thank you for choosing Black-Haak! If you have the time, please fill out our
Furnace start up. Cycled system. Checked wiring. Checked drain lines and venting, ok. Checked gas pressures, ok. Checked for co in airstream, none found. Normal levels of co and XS air found in exhaust. Fan speed is normal. 45 in temp rise. Checked aprilaire, found system dry and not operating. Possible clogged water feed line. Customer will look at it and call us if he needs repairs. System operating normal at this time. Job complete.
Furnace clean and tune. Cycled system. Checked heat exchanger, found several rust spots but no cracks at this time. Igniter is ok. Cleaned and checked burners and flame sensor. Found some indications of ventor bearing ware. Checked for CO and XS air in exhaust, normal levels found. No CO found in airstream. System is worn, but operating normal at this time. Job complete. home warranty. Customer owes nothing.
Blower motor is replaced. Rewired, bracketed, and cycled. Unit is operating normally at this time.
I replaced capacitor and cycled system on found that the fan was not spinning, I then checked voltage at the board and got 120 going to the blower motor. This system will need a new blower motor due to age, condition, and cost to repair I recommend replacing the system. Job complete
Furnace clean and tune. Cycled system. Checked heat exchanger. Found it very rusted. Found several weak spots, but no cracks worn through at this time. Checked igniter, worn but tested ok at this time. Checked and cleaned flame sensor and burners. Burners are very corroded and worn. Found ventor motor bearings worn. Checked for CO and XS air levels in exhaust. CO levels normal but, XS air levels are elevated. Levels were 220. Possible issues with secondary heat exchanger. Found a few cracks in transition assembly. Evidence of water leaks from those cracks under ventor motor. System is very worn with multiple concerns for failure in future operation. Average life of this unit is 14 years with yearly maintenance. No CO found in airstream at this time. Job complete. Furnace portion complete. Balance for ac portion in spring.
Completed installation of a 4â€ galvanized dryer vent piping. Routed pipe from back of the dryer to ceiling in basement and then to the east side of home and out the box sill. Installed a black 4â€ vent hood on exterior of building terminating the dryer vent. Run tested dryer to check for air flow and found it to be working properly. Thank you for choosing Black-Haak. Please take a moment to fill out our online survey.
Completed installation of an Aprilaire model 600 humidifier. Placed the humidifier on the plenum and ran a 6â€ bypass to the return drop. Ran a 1/4â€ copper line from the hot water line of the water heater to the humidifier to supply it with water. Ran a drain hose from humidifier to existing furnace drain hose and tied them together. Ran all control wiring between the duct mounted humidistat and the humidifier to the furnace and connected it all. Run tested the humidifier and went over operation with Mary. Thank you for choosing Black-Haak heating. Please take a moment to fill out our online survey.
Performed furnace first year cleaning, inspected exhaust and intake PVC ensuring all connections were secured, I then removed and cleaned the burners along with the flame sensor, next I cycled the system on and checked gas pressures, lastly performed a combustion test verifying no CO in the airstream. This system is currently operating normal at this time. Job complete
Was here for a furnace start up. Performed preferred customer furnace start up. Completed furnace start up form. Furnace is running normally at this time.
Completed gas furnace replacement. Disconnected the old furnace and removed it from house. Set new furnace on blocks and reconnected the electric, gas, pvc venting and ductwork. Ran a new thermostat wire and installed a new WiFi thermostat, then connected to the furnace. Ran new drain hose for the furnace, AC and humidifier and routed it to the floor drain. Run tested the furnace but will still need a technician start up. Thank you for choosing Black-Haak. Please take a moment to fill out our online survey.
Furnace safety inspection. Cycled system. Found ventor motor has a lot of vibration to it. Removed igniter/flame rod, found it worn. Checked heat exchanger, very rusted with cracks forming. Burners are very rusted and worn. System lights very hard. Found indications of leak from ventor motor. Standing water under motor. Rusting found in blower compartment. Blower motor also has vibrations and noisy operation. Found heavy rusting on ignition tube. Normal levels of CO and XS air in exhaust. No CO found in airstream. Average life of this unit is 14 years. Due to age, condition, and cost to repair, second opinion recommended. Office to follow up on call. Job complete. Office to schedule second opinion. No charge due to second opinion.
Performed level 2 furnace cleaning. Burners and flame sensor are clean. Heat exchanger looks good. Gas and exhaust levels are normal. No CO detected in the air. Drain is clear. Heat rise was 58 degrees. Unit is operating normally at this time.
Was here for a furnace cleaning. Performed preferred customer furnace cleaning. Customer was concerned about the furnace lighting intermittently. While watching the furnace light. The gas valve would energize and wouldnâ€™t open some of the time. Checked the gas pressure. Found that the incoming gas pressure is at 18 inches of water column. Normally there is only supposed to be around 8 inches of water column. Found that a gas regulator on the outside of the building is bad. Called the office to have an installer come to change out the regulator. The installers came and replaced the regulator. Rechecked the gas pressure. The gas pressure looks good. Cycled the furnace a couple of times. Furnace is running normally at this time.
11-15-18 installed 2 stage daikin. Cycled furnace to make sure everything was working.
Performed level 2 furnace cleaning. Burners and flame sensor are clean. Heat exchanger looks good. Gas and exhaust levels are normal. No CO detected in the air. Drain is clear. Heat rise was 44 degrees. Unit is operating normally at this time.
Performed furnace safety check; I cycled the system on and performed a powder test and did get blow back from all 3 cells, I then performed a combustion test and found a high amount of excess air in the exhaust, I also ohmed out the igniter, lastly inspected the heat exchanger and found a large amount of rust, this system is currently operating at this time. But due to age and condition I do foresee issues in the future. Job complete
Came to investigate a no heat. Furnace would try to ignite, and fail. Proper voltage wasnâ€™t going to the gas valve. Pressure switch had proper voltage. I blew the lines clear and tried adjusting it to no success. Main board is not sending proper voltage to the valve. Board needs to be replaced. Update, after returning, we found the drain was leaking water and the hose was clogged with a table. We moved the table and cleared the line of debris and kinks. This cause the pressure switch to trip and not allow voltage to the gas valve. Unit is up and running at this time.
Replaced burners and cycled system on. Everything is operating normal at this time job complete.
I performed the boiler clean and tune. The boiler is operating properly. We need to quote a price to replace a 2 foot and 4 foot section of baseboard in the bathroom. The office will call back with a price for that.
Furnace clean and tune x2. Upstairs furnace. Cycled system, system would not light. Removed and cleaned flame sensor, reinstalled and cycled again. System then lit. Checked heat exchanger and found rust. Burners are extremely rusted causing the flame to travel inconsistently down heat exchanger. Found ventor motor bearing very worn and noisy. Furnace had major condensation leak from drain lines. Customer purchased drain line and had it installed with the end of the drain line out of open burner compartment door, draining onto floor of basement. I used existing clamps and secured drain line correctly from exhaust vent to drain trap. Gas pressure dropped dramatically from 2nd to 1st stage, causing flame to almost die out. This system is in very poor shape, and failure is expected. Normal levels of CO found in exhaust. Higher levels of XS air found in exhaust. Second opinion recommended. First floor furnace. Cycled system. Checked heat exchanger, found it very rusted with cracks startin
We removed the old furnace and ac. installed a new units. Tie into existing duct, gas line, venting and electric. Ran new drain. Flushed the lineset and brazed all joints. Left filled with nitrogen till spring
We are here to serve your Fox Valley home or business!
Copyright © 2018 | Black-Haak Heating, Inc | All Rights Reserved